Carbon A572 (ASTM A572) is a low alloy, high strength steel, popular for its strength. With a better strength to weight ratio, A572 steel is a natural step up from A36 when more strength is needed. The increased strength of A572 plate does not compromise the steels ductility and weldability. A572 plate can therefore be formed, welded, and machined. A572 Grade 42, 50, 55, 60, 65 Steel Plates Leeco Steel, LLCMaterial Properties The following material properties are ASTM specifications and will be confirmed on the Mill Test Report. Grade Yield Point (ksi) Tensile Strength (ksi) Min. 8" Elongation % 42 42 60 20 50 50 65 18 55 55 70 17 60 60 75 16 65 65 80 15 Chemical Composition The following composition properties are ASTM specifications for the A572 grades. Grade 42 + Grade 42 Carbon max 0.21%
A572 Grade 50 steel specification is for a high-strength, low alloy (HSLA), hot rolled structural steel plate. A low carbon, low alloy steel, these plates have a flat, clean surface. Excellent formability and weldability are characteristic of this grade. A572 gR.50 steel Cutting A572 can be cut with plasma, oxy-Acetylene, laser, and water jet ASTM A570 GR50 Hot-rolled Carbon structural steel,ASTM ASTM A570 GR50 is a kind of hot-rolled carbon structural steel . There are seven levels or grades in the standard ASTM A570 .They are ASTM A570 GR30, A570 GR33, A570 GR36, A570 GR40, A570 GR45, A570 GR50, A570 GR55 . ASTM A572 Grade 42/50 Carbon Steel Plates, ASTM A572 Grade Ganpat Industrial Corporation is also one of the well known supplier and trading house for high quality ASME SA 572 Gr. 50 Carbon Steel Coils, which are characterized by high chromium (19 % 32 %) and molybdenum (up to 5 %) and lower nickel contents than austenitic stainless steels.
ASTM A572 Specification refers to High-Strength Low-Alloy Steel Plate for structural building, among the 5 steel grades of 42, 50, 55, 60 and 65, Grade 50 is one most common steel in applications where need more strength and less weight, use steel plate of this grade other than ordinary carbon steel will make the steel structure with same steel strength but lighter weight. ASTM A572 Gr 50 steel material can be ASTM A572 Steel - Ultra-High Strength - CopperloyA572-50 steel ramps have a carbon content between 0.050.25% that gives excellent formability and is an excellent material for strong and safe welds. A572-50 HSLA steel is versatile and easy to cut. You can cut A572-50 with plasma, oxy-Acetylene, laser, water jet, and abrasive cut-off saws. ASTM A572 Steel AngleASTM A572 Steel Angle ASTM A572 steel angle is another high-strength, low-alloy (HSLA) columbium-vanadium steel sections. Owing to small amount of columbium & vanadium alloy elements, hot rolled A572 steel angle has better properties than carbon steel A36. First, A572 has higher strength than A36 like in yield strength and tensile strength.
A572 Gr.50 steel plate is typically used whenever a cost savings from a weight reduction can be gained. Bebon will supply ASTM A572-Gr50 plates up to 150mm thickness. A588 Gr.A steel, similar to ASTM A572-Gr50, is also a high strength low alloy steel, but is a Copper Bearing steel offering approximately four times the corrosion resistance of structural carbon steel grade. High Strength Steel Angle-Carbon Steel Profile SupplierASTM A36 and JIS G3192 steel angle is one of the most widely used carbon steel section in the construction industry and project. It is a low-cost material and shows the required strength property compared with other steels. It is popular also for its good weld PRODUCT GUIDES - Central Steel & Wire Co.ASTM A 588 Gr 50 aka Cor-Ten* 3/16 - 1-3/4 50 70 90° 2 t transverse Plate Flat rolled finished steel products within the following: -Carbon and HSLA steel with specified minimum yield thru 80,000 psi. -Tolerances applicable to any 12 ft. of length, measured as maximum deviation from a
ASTM A572 Grade 50 Plate. Tolerance Over Specified Thickness, For Widths Given, in Inches. Tolerance under specified thickness .010". A 3/4 x 52" wide plate, for example, would have a tolerance range of .740/.780". Because of tolerances, i.e. thickness, flatness and camber, as well as the hot roll condition, ASTM A572 Grade 50 generally does not finish to specified thickness. Steel Plate Comparisons Precision Grinding, Inc.Among the least expensive of the carbon steels. Very good welding properties along with 36ksi yield strength. Considered a mild steel due to hardness. A572-42 A572-50:A572 grade 50 steel plate is a high-strength, low-alloy plate, specified for bridges, higher strength structural duties, and light pressure vessel requirements. Recommended for riveted, bolted, or welded structures, such as Gussets and Steel Reference Guide - Glosser SteelASTM A572 - High-Strength Low-Alloy Structural Steel This specification covers high-strength structural quality shapes generally suitable for use in riveted, bolted, or welded construction, and for general structural purposes.
We offer carbon sheet coated, cold rolled, hot rolled, painted and as expanded metal. Common applications range from construction framing and ductwork to machinery framing. Available grades include CS B, FS B, DS-B, DDS, EDDS, A36, A572-50, SS Grades 30-55 HSLA Grades 40-80 and A606. Steel Structurals - Alro SteelASTM A992/A572 (Grade 50) Tensile Strength:65,000 min. PSI Yield Point:50,000 min. - 65,000 max. PSI Nominal (lbs./ft)Depth Weight A Depth of Section D Flange Thickness B Width of Flange C Thickness of Web A WeightC B Depth (lbs./ft.) Thickness of Web Width of Flange 6" 4.4 .114 1.844ASTM A572 Steel Plate__Steel SupplierASTM A572 standard specification high strength low alloy Columbium-Vanadium structural steel plates A572 Grade 42, A572 Grade 50, A572 Grade 55, A572